Bingo Plus stock

List of catalogs of this article:

• 1,Bingo Plus stock LF1 Engine ParametersNumber
• 2, lfw Engine parameters
• 3, What is the difference between LFW engine and LZC engine?
• 4, Hello! How many torques is the spindle of Buick LFW engine?

LF1 engine parameters

1. This engine adopts a cast aluminum cylinder block and double overhead camshaft design, with a maximum power of 191kW and a maximum torque of 350N·m. In addition to the LF1 engine, Buick Junyue is also equipped with other models of engines, such as 0T, 5L, etc.

2. Cadillac CTS 0 version adopts this LF1 Engine, The Maximum Torque Of Up To 300Nm Is Only Slightly Lower Than That Of The Old 6L Engine, But The Power Is Higher Than 3Kw.

3. When there is a traffic jam or idle for a long time, the engine water temperature gauge display is too high, the high-speed working time of the electronic fan is too long, the engine noise increases, and the fault is the most obvious when the air conditioner is turned on when the temperature is too high. Check whether there is too much dust between the condenser and the water tank, and clean it thoroughly with high-pressure air to ensure that the water tank and The condenser has good heat dissipation performance.

4. When the valve is opened, the pressure difference and the high pressure of the gas itself increase the air intake and improve the power; the naturally aspirated engine has a direct impact on the stability and responsiveness of the power output, which is far better than the supercharged engine. The current V84LF1 engine is the best example.

5. About 14 oil in urban areas, and about 10 oil on high speed.

lfw engine parameters

1, LFW engine is a multi-fuel version of LF1 engine.

2. Hello, yours should be a 0LFW engine. Please check whether the long-term fuel adjustment value of cylinder 2 is about -20, and then the exhaust pipe has white smoke, such asIn this way, it is recommended to replace the high-pressure oil pump and fuel injector. I hope my advice can help you [If there is a problem with the car, ask the car master. 4S store professional technician, 10 minutes to solve.

3. The full name is F119-PW-100, which is a dual-rotor small-channel ratio-forced turbofan engine developed for the F-22A. It adopts a two-dimensional vector nozzle that can be deflected up and down. The up and down deflection angle is 20 degrees, and the thrust and vector are controlled by the digital electronic system. Main parameters of F119: length 826 meters, maximum diameter of 13 meters, weight of 1360 kilograms, maximum thrust of 156 kn, thrust-to-weight ratio of 17.

4. II. Mechanical failures are mainly due to insufficient cylinder pressure, such as loose valve closure, air leakage, excessive gap between the cylinder, piston and piston ring, resulting in insufficient compression ratio in the cylinder, etc.The lack of cylinder operation of the engine will bring great harm: the speed and power of the engine decrease. Increase fuel consumption and emission pollution.

5. L engine, with a maximum power of 82kw and a peak torque of 150Nm; while the high-configuration model adopts an 8L model with higher power, with a maximum power and torque of 103kw and 180Nm respectively. However, both engines are only equipped with a five-speed manual transmission, and there will be no four-wheel drive version.

6. The Dongfeng engine is mainly located on the left side of the engine, which is relatively close to the position of the cylinder head, that is, the position between the engine and the transmission. It is almost invisible by visual measurement, so you need to lift the vehicle to observe. There is also an engine number on the driving license, which is a 17-digit character.

What is the difference between LFW engine and LZC engine?

different. LZC has added a VVT system, that is, variable positive time. The LW9 engine is not a variable gas time. Therefore, the assembly requirements of the LZC engine are different, and the gap of each part should be small to ensure the sufficient oil pressure and oil volume of VVT.

LZC engine is a variable gas distribution timer, while the LB8 or LW9 engine is not a variable gas distribution timer, so the assembly requirements of the LZC engine are different, and the gap in each part should be small to ensure the sufficient oil pressure and oil volume of VVT. The oil pressure of the LZC engine must be maintained above 200KP, and the oil pressure is the cause of such failures.

The assembly requirements of LZC engines are different, and the gap between parts should be small to ensure sufficient oil pressure and oil volume of VVT.The oil pressure of the LZC engine must be maintained above 200KP, and the oil pressure is the cause of such failures.

The LFW engine is a multi-fuel version of the LF1 engine.

Hello! How many torques is the spindle of Buick LFW engine?

The torque of the old Jetta spindle tile screw is: the torque of the old Jetta spindle tile screw is more than 150N·m.

The spindle torque of the Xinchai 490 engine is 132-158/N.m, the torque of the tile connecting rod is 91-116/N.m, and the torque of the tile cylinder head is 116-132/N.m.

Cylinder head bolt 29NM plus turning angle 130 degrees spindle tile cover 25NM plus turning angle 40 degrees connecting rod tile 8Nm plus turning angle 90 degrees.BYD473QE engine is a new 5L gold displacement all-aluminum alloy engine independently developed by BYD, with a maximum power of 80kW and a maximum torque of 145Nm.

Engine models are different, and the torque is also different: (1) The torque of the connecting rod tile cover is smaller than that of the crankshaft tile cover; (2) The torque of diesel vehicles is larger than that of gasoline vehicles; (3) How much torque is specifically required is generally carried out in accordance with the regulations and instructions.

If the tile mouths are on the right. The two tile mouths are pressed together, and they are not staggered.

The torque of the spindle screw of the bell engine is about 15 to 16 kg.